5PCS 2.8V-6V LED Driver 1.5A 30-1500MA Constant Current PWM Control Board Module

Description

5PCS 2.8V-6V LED Driver 1.5A 30-1500MA Constant Current PWM Control Board Module
Description:
LD06AJSA / B is a current regulation integrated circuit operating from an input voltage of 2.8 V to 6 V, the constant output current can be set to 1.5A with an external resistor. the LD06AJSA / B consists of high precision reference voltage, amplifier, current mirror, etc. The on-chip power transistor and current block sense significantly reduce the number of external components, which makes the LD06AJSA / B ideal for LED driver.
When the CE pin is high, the input voltage is greater than 2.8 V, and is higher than the direct voltage LED plus the required voltage drop, LD06AJSA / B normally operates to provide constant current from the PULLOBEE. The LD06AJSA / B adopts temperature regulation instead of temperature protection function, the temperature regulation can cause the LEVOU to be switched on continuously in case of high ambient temperature or high voltage fall. When the LD06AJSA / B temperature junction reaches about 135 ° C, the internal temperature setting of the block reduces the current so that the temperature of the LED junction will not rise further. this feature allows users to maximize the use of the power handling ability of the chip, do not worry about the chip overheating and damage to the chip or external components.
The LD06AJSA / B also has the function of allowing the chip, which can the whole chip to limit the shutdown current consumption within 1uA.
The LD06AJSA / B also adopts the current overload protection block. When the current LED 1.9A approaches (Typical), the on the current block protection starts the function to prevent the current LED from increasing.
Application 1: Wiring according to the following figure, use a suitable screwdriver carefully and slowly rotate the adjustable resistance.
Application 2: Adjust the adjustable resistance to 0 ohms (or maximize the current according to Order 1) and then use the MCU output current output of the PWM signal to control the LED
the frequency of the PWM signal must be less than 2 KHz
Specifications:
Operating voltage: DC 2.8-6 V (Perfect for 3 V 3.3 V 3.7 V 4.5 V 5 V 6 V LED Driver)
Output Current: 30-1500MA
Maximum output power: 9 W
Can drive 1-16 pcs 2.8-6 V LEDs (maximum current does not exceed 1.5A)
Current regulations: 1 through adjustable resistance; 2 through PWM signal control
Temperature Control Chip
Took more than Current Protection
Operating Temperature Range
Size: 1.8x1cm/0.71x0.39"
Quantity: 1 Pc
Note:
1.Transition: 1cm=10mm=0.39inch
2.Please allow 0-3mm error due to manual measurement. pls make sure you do not mind before you bid.
3.Due to the difference between different monitors, the picture may not reflect the actual color of the item. Thank you!
Package Included:
5PC*LED Driver
Payment
Shipping
Refund
Payment
We only accept payment through Paypal.
Items will go to post within 1-2 business days after payment confirmed.
Shipping
1. We ship to Worldwide.
2. We only ship to confirmed PAYPAL address; your PAYPAL address must match your Shipping address.
3. Any non-received items caused by invalid address registered on PayPal are not in our full refund or replacement policy. Shipping fee has including the local handing and packaging fee.
4. All the items will be shipping within 1-2 working days after receiving the payment, except some holidays.
5. We will not be responsible for any custom delay or tax, because transit time is highly depended and provided by postal Service.
6. If you have any problem, please contact us via message, we will reply message within 1-2 working days, please wait for patient.
Refund
If you can't receive the product within 2 months (60 days), please contact with us,we promise to payback 100% of your money.
We ensure our products work normally before post.If the products is broken before arrival to you,all you should do is taking a photo to show us our broken product.We promise to payback 100% of your money.
If the item is defect when you receive it or you are not satisfied with it, please return it within 14 days for a replacement or money back. But the items must be back in factory condition. Please contact us and double check the return address before you return it.
If is item is defective in 12 months, you can return it to us. We will send you a new replacement after receiving the defective item.
On Dec-10-20 at 06:16:06 PST, seller added the following information: