DIY Attiny programming & development shield Arduino - ATtiny85 /45/25 Programmer

Description

DIY - ATtiny programming shield for Arduino UNO - ArduinoISP Attiny85 Programmer.
This Arduino compatible shield helps you
extend any old Arduino board to a nice clean ATtiny programmer
.
This DIY kit comes with all needed parts we even includ some extra fine solder for SMD parts - There are some SMD parts that can be ordered assembled, check the variations
.
The shield has two 8 pin sockets - The upper one is for programming and the lower one is for testing
.
The board has three leds indicators for the programming procedure, and two more for testing. Also features two on board buttons that can reset the the Arduino board and the Attiny chip.
This shield is following the
ArduinoISP tutorial
and you should follow the steps to load the firmware needed to the arduino board before attaching the shield.
Follow these steps for preparing the arduino board (Follow this tutorial - arduino.cc/en/Tutorial/ArduinoISP):
We also included a detailed instruction sheet that is sent to you with the shield.
Open the ArduinoISP firmware (in Examples) to your Arduino board.
Note for Arduino 1.0: you need to make one small change to the ArduinoISP code. Find the line in the heartbeat() function that says "delay(40);" and change it to "delay(20);".
Select the items in the Tools > Board and Serial Port menus that correspond to the board you are using as the programmer (not the board being programmed).
Upload the ArduinoISP sketch.
Attach your Attiny programmer shield.
Select the item in the Tools > Board menu that corresponds to the board on which you want to burn the bootloader (not the board that you're using as the programmer). See the board descriptions on the environment page for details.
Select the Arduino as ISP in the Tools>Programmer menu.
Use the Burn Bootloader command.
Further details and Notes:
The Attiny programming shield is a great solution for fast, clean and professional sketch upload to your attiny project. Attiny allows you to shrink and cut cost of any project you do it has a wonderful active community and its the right Micro-controller for beginner and advanced makers.
Compatibility:
Compatible with Arduino UNO - all versions and most of clones
.
Supported Attiny Chips:
Supports Attiny 11,12,13,13A,13V,25,45,85 (Package 8-PDIP)
. labore et dolore magna aliquyam erat.
Programming Indicators:
3 Indicator LEDsfor the programming process
.
Testing Indicator:
2 Testing LEDs attached to pins 0,1 (PB0, PB1).
Breakout Board:
Testing socket has female headers that correspond the ATtiny pin-out - Use it as your breakout board.
Not included:
Arduino board, ATtiny chips.
Included:
Shield PCB, All parts, Instructions, A bit of Extra fine solder (For SMD parts) and a small gift :)
Contact us
We can be contacted at any time through eBay messages if you have any questions, comments or product requests. We normally respond within 1 - 2 working days - and do our best to help you out! We encourage our customers to contact us with any questions or concerns! We'd like to be sure you are completely satisfied with your purchase.
Payment
We accept only PayPal.
Please make your payment within 7 working days after auction ends or the order is placed.
We will leave positive feedback to a buyer as soon as the buyer pays for the item. Please leave us 5-star rating. Any problems please contact us first, many thanks!
Our normal business hour is Sunday to Friday 9:00am to 6:00pm NY Time. All emails and orders will NOT be processed during weekends and holidays.
We welcome wholesales and any deal offers, Please contact us first if you have any questions.
Shipping
We ship Worldwide.
We only ship to confirmed PayPal accounts - Your PayPal address must match your Shipping address.
We carefully pack the products and use only high quality packing materials.
Any issues that are caused by address mistakes will not be covered by us.
All the items will be shipping within 1-2 working days after receiving the payment.
We will not be responsible for any customs delay or tax, because transit time is highly depended and provided by local postal services.
If you have any problem, please contact us via eBay messages (contact seller), we will reply within 1-2 working days.
Returns
If you did not receive the package within 2 months (60 days), please contact us - We will refund 100% of your money.
We ensure our products work normally before post.
If the products is broken before arrival to you, all you should do is taking a photo to show us our broken product.
If the item has a defect when you receive it or you are not satisfied with it, please return it within 14 days for a replacement or money back (must be back in factory condition).
Please contact us and double check the return address before you return it.
SIKTEC & SIKDEV 2020 - Inovative Solution Development