STLINK-V3MINI Compact in-circuit Debugger Programmer for STM32

Description

This auction is for
STLINK-V3MINI
STLINK-V3MINI, compact in-circuit debugger and programmer for STM32 microcontrollers
Description
The STLINK-V3MINI is stand-alone debugging and programming mini probe for STM32 microcontrollers.
The JTAG/SWD interfaces are used to communicate with any STM32 microcontroller located on an application board.
The STLINK-V3MINI also provides a Virtual COM port interface allowing the host PC to communicate with the target microcontroller through one UART.
The STLINK-V3MINI is a portable version, easy-to-use debugger/programmer including STDC14 interface with its flat cable.
Key Features
Stand-alone probe
Approximately 15 x 30 mm high-density integration PCB, very small form factor
Self-powered through a Micro-B USB connector (does not provide power supply to the target application)
USB 2.0 high-speed compatible interface
Direct firmware update (DFU) support, to use with more future devices
JTAG / serial wire debugging (SWD) specific features:
3 V to 3.6 V application voltage support and 5 V tolerant inputs
Delivered with 1.27 mm pitch STDC14 to STDC14 flat cable
Additional adapter board and 2.54 mm pitch 20-pin JTAG/SWD flat cable (extra accessories from Waveshare)
SWD and serial wire viewer (SWV) communication support
Virtual COM port (VCP) specific features:
3 V to 3.6 V application voltage support on the UART interface and 5 V tolerant inputs
VCP frequency up to 15 MHz
Drag-and-drop Flash programming
Two color LEDs: communication, power
Includes STDC14 signals protection
Supported Software
STM32CubeProgrammer
Keil® MDK-ARM
IAR™ EWARM
SW4STM32
STVP
GCC-based IDEs
Supported Devices
All STM32 MCUs with JTAG / SWD interface
Specification Comparison among Different STLINK Versions
Comparison
STLINK-V3SET
STLINK-V3MINI
ST-LINK/V2
Remarks
JTAG/SWD application voltage
3V - 3.6V
3V - 3.6V
1.65V - 3.6V
ST-LINK/V2 supports STM32 low-power devices
SWIM application voltage
1.65V - 5.5V
N/A
1.65V - 5.5V
STLINK-V3MINI doesn't support SWIM of STM8
SWV support
YES
YES
YES
only available for STM32 at present
Debug interface
multi
multi
2
STLINK-V3SET/MINI feature GPIO port besides the programming port
LED indicator
two colors
two colors
two colors
two colors LED indicates both power and communication, while red color LED indicates only communication
Example
Note: the STM32 application board in the photo is NOT included.
Connect to PC
The STLINK-V3MINI should be connected to the PC via a USB Micro-B cable.
Before connecting, install/update the ST-LINK toolset to support the STLINK-V3MINI (drivers)
STLINK-V3MINI adopts an STM32 F7 microcontroller, supports USB2.0 high speed communication
Connect to STM32 applications
The STLINK-V3MINI can be connected to STM32 target applications on JTAG / SWD interfaces.
Connection Method A: connect to target application directly via the onboard STDC14 connector.
Connection Method B: connect to target application via the STLINK-V3MINI Adapter board.
STLINK-V3MINI LED Status
COM LED is blinking RED:
the first USB enumeration with the PC is taking place.
COM LED is RED:
communication between STLINK-V3MINI and the PC is established (end of enumeration).
COM LED is blinking GREEN/RED:
data are being exchanged between the target and the PC.
Dimensions
Development Resources
Wiki :
www.waveshare.com/wiki/STLINK-V3MINI
Package Contains
STLINK-V3MINI official content x1
STLINK-V3MINI Adapter x1
USB type A plug to micro B plug cable x1
20-pin JTAG/SWD flat ribbon x1
3-pin 2.54mm pitch squid wire x1