T-Beam ESP32 433/868/915Mhz WiFi Bluetooth ESP32 GPS NEO-6M With OLED

Description

Home
Electronic Component
Chips
Sensor
Arduino Module
Raspberry Pi
T-Beam ESP32 433/868/915Mhz WiFi Bluetooth ESP32 GPS NEO-6M With OLED
Popular
Popular
Product Introduction
Product Demonstration
（
Note:OLED is not soldered to T-BEAM）
Product Features
ESP32
Lastest ESP32 Version: REV1
WIFI
Bluetooth
8MB PSRAM
4MB Flash
3D Antenna
LORA
Product Description
Working voltage: 1.8~3.7v
Acceptable current：10~14mA
Transmit current: 120mA AT +20dBm
90mA AT +17dBm
29mA AT +13dBm
Operating frequency: 433/470MHz(433HMz version) /868M/915M(868MHz version)
Transmit power: +20dBm
Receive sensitivity :-139dBm AT LoRa &62.5Khz&SF=12&146bps
-136dBm AT LoRa &125Khz&SF=12&293bps
-118dBm AT LoRa &125Khz&SF=6&9380bps
-123dBm AT FSK&5Khz&1.2Kbps
Frequency error：+/-15KHz
FIFO space ：64Byte
Data rate ：1.2K~300Kbps AT FSK
0.018K~37.5Kbps AT LoRa
Modulation Mode ：FSK,GFSK,MSK,GMSK,LoRa TM，OOK
Interface form ：SPI
Sleep current ：0.2uA AT SLEEP
1.5uA AT IDLE
Operating temperature ：-40℃- +85℃
Digital RSSI function
Automatic frequency correction
Automatic gain control
Low voltage detection
Fast wake-up and frequency hopping
Highly configurable data packet handler
GPS
GPS modules NEO-6M, 3V-5V power supply Universal
Destined module with ceramic antenna, signal super
Save the configuration parameter data EEPROM Down
With data backup battery
There are LED signal indicator
Default Baud Rate: 9600
Power
Power Supply Input
USB 5V/1A
Charging current
500mA
Battery Input
3.7-4.2V
Charge IC
AXP192
OLED Description:
1.Size
:
0.96 inch
2.High resolution
:
128 * 64
3.Color
:
white
4.Viewing angle
:
> 160 °
5.Driver IC
:
SSD1306
6.Working temperature
:
-30  celcius ~ 80  celcius
7.Module volume (generous)
:
27.0MM * 27.0MM * 4.1MM
8.Supports many control chip
:
Fully compatible with Arduino, 51 series, MSP430 series,
STM32/2, CSR chip, etc.
(a lot of routines for reference)
9.Wide voltage support
:
without any modification, directly supports 3.3V ~ 5V DC
10.Ultra-low power consumption
:
Normal operation Is 0.04W
11.IO port occupies minimal display
:
The IIC communication,as long as the two IO ports
More information:
https://github.com/geeksville/Meshtastic-Android/blob/master/README.md
https://github.com/meshtastic/Meshtastic-device/releases\
https://github.com/Xinyuan-LilyGO/LilyGO-T-Beam
Pin Schematic
Size picture
Shipping List
433MHz/868MHz Version
1 X TTGO T-Beam
1 X 433MHz/868MHz Antenna
1 X 0.96 inch 128X64  OLED
2 X Pin
Note: OLED is not soldered to T-BEAM
915MHz/923MHz Version
1 X TTGO T-Beam
1 X 915MHz/923MHz Antenna
1 X 0.96 inch 128X64 OLED
2 X Pin
Note:OLED is not soldered to T-BEAM
Payment
Shipping
Refund
Payment
We accept PayPal only.
But we only
Accept
your
Ebay Address
,Please Make sure it's 100% right.
Payment must be received in 5 business days of auction closing.
Please leave note for your special request (e.g. Colors or Size) in PayPal when you pay the order.
Any special request cannot be accepted after 24 hours of payment, because most of orders will be processed instantly and same day dispatched.
Shipping
We maintain high standards of excellence and strive for 100% customer satisfaction! Feedback is very important to us. We request that you contact us immediately BEFORE you give us neutral or negative feedback, so that we can satisfactorily address your concerns.
Refund
All package need to
wait 30 days
(US only n
eed 7-10 days)
,
Please take care it.Less than 30 days,we can't take a refund
.
If the item is defect when you receive it or you are not satisfied with it, please return it within 14 days for a replacement or money back. But the items must be back in factory condition. Please contact us and double check the return address before you return it.
If is item is defective in 12 months, you can return it to us. We will send you a new replacement after receiving the defective item.
Home
Electronic Component
Chips
Sensor
Arduino Module
Raspberry Pi
T-Beam ESP32 433/868/915Mhz WiFi Bluetooth ESP32 GPS NEO-6M With OLED
Product Introduction
Product Demonstration
（
Note:OLED is not soldered to T-BEAM）
Product Features
ESP32
Lastest ESP32 Version: REV1
WIFI
Bluetooth
8MB PSRAM
4MB Flash
3D Antenna
LORA
Product Description
Working voltage: 1.8~3.7v
Acceptable current：10~14mA
Transmit current: 120mA AT +20dBm
90mA AT +17dBm
29mA AT +13dBm
Operating frequency: 433/470MHz(433HMz version) /868M/915M(868MHz version)
Transmit power: +20dBm
Receive sensitivity :-139dBm AT LoRa &62.5Khz&SF=12&146bps
-136dBm AT LoRa &125Khz&SF=12&293bps
-118dBm AT LoRa &125Khz&SF=6&9380bps
-123dBm AT FSK&5Khz&1.2Kbps
Frequency error：+/-15KHz
FIFO space ：64Byte
Data rate ：1.2K~300Kbps AT FSK
0.018K~37.5Kbps AT LoRa
Modulation Mode ：FSK,GFSK,MSK,GMSK,LoRa TM，OOK
Interface form ：SPI
Sleep current ：0.2uA AT SLEEP
1.5uA AT IDLE
Operating temperature ：-40℃- +85℃
Digital RSSI function
Automatic frequency correction
Automatic gain control
Low voltage detection
Fast wake-up and frequency hopping
Highly configurable data packet handler
GPS
GPS modules NEO-6M, 3V-5V power supply Universal
Destined module with ceramic antenna, signal super
Save the configuration parameter data EEPROM Down
With data backup battery
There are LED signal indicator
Default Baud Rate: 9600
Power
Power Supply Input
USB 5V/1A
Charging current
500mA
Battery Input
3.7-4.2V
Charge IC
AXP192
OLED Description:
1.Size
:
0.96 inch
2.High resolution
:
128 * 64
3.Color
:
white
4.Viewing angle
:
> 160 °
5.Driver IC
:
SSD1306
6.Working temperature
:
-30  celcius ~ 80  celcius
7.Module volume (generous)
:
27.0MM * 27.0MM * 4.1MM
8.Supports many control chip
:
Fully compatible with Arduino, 51 series, MSP430 series,
STM32/2, CSR chip, etc.
(a lot of routines for reference)
9.Wide voltage support
:
without any modification, directly supports 3.3V ~ 5V DC
10.Ultra-low power consumption
:
Normal operation Is 0.04W
11.IO port occupies minimal display
:
The IIC communication,as long as the two IO ports
More information:
https://github.com/geeksville/Meshtastic-Android/blob/master/README.md
https://github.com/meshtastic/Meshtastic-device/releases\
https://github.com/Xinyuan-LilyGO/LilyGO-T-Beam
Pin Schematic
Size picture
Shipping List
433MHz/868MHz Version
1 X TTGO T-Beam
1 X 433MHz/868MHz Antenna
1 X 0.96 inch 128X64  OLED
2 X Pin
Note: OLED is not soldered to T-BEAM
915MHz/923MHz Version
1 X TTGO T-Beam
1 X 915MHz/923MHz Antenna
1 X 0.96 inch 128X64 OLED
2 X Pin
Note:OLED is not soldered to T-BEAM
Payment
Shipping
Refund
Payment
We accept PayPal only.
But we only
Accept
your
Ebay Address
,Please Make sure it's 100% right.
Payment must be received in 5 business days of auction closing.
Please leave note for your special request (e.g. Colors or Size) in PayPal when you pay the order.
Any special request cannot be accepted after 24 hours of payment, because most of orders will be processed instantly and same day dispatched.
Shipping
We maintain high standards of excellence and strive for 100% customer satisfaction! Feedback is very important to us. We request that you contact us immediately BEFORE you give us neutral or negative feedback, so that we can satisfactorily address your concerns.
Refund
All package need to
wait 30 days
(US only n
eed 7-10 days)
,
Please take care it.Less than 30 days,we can't take a refund
.
If the item is defect when you receive it or you are not satisfied with it, please return it within 14 days for a replacement or money back. But the items must be back in factory condition. Please contact us and double check the return address before you return it.
If is item is defective in 12 months, you can return it to us. We will send you a new replacement after receiving the defective item.