XBee DigiMesh 2.4 RF Module, 1 mW, PCB Antenna

Description

XBee DigiMesh 2.4 RF Module, 1 mW, PCB Antenna
XB24-DMPIT-250
Wireless connectivity using the DigiMesh protocol
XBee DigiMesh 2.4 delivers end-point device connectivity with a globally deployable
2.4 GHz
transceiver. These modules use the innovative DigiMesh networking protocol. This innovative, peer-to-peer protocol offers users added network stability through self-healing, dense network operation and support for sleeping routers, extending the operational life of battery-dependent networks.
Part of the XBee family of wireless products, these modules are easy to use, share a common footprint, and are fully interoperable with other XBee products utilizing the same technology. This allows different XBee technologies to be drop-in replacements for each other; you can switch between 802.11, 802.15.4, ZigBee, DigiMesh and proprietary long-range with minimal development time or risk.
The XBee 2.4 DigiMesh modules use the same hardware as the XBee 802.15.4 modules. It is possible to change from one platform to the other by loading different firmware onto the same module.
DigiMesh Protocol
DigiMesh is a proprietary mesh networking protocol. Its features include:
Self-healing
— Any node may enter or leave the network at any time without causing the network as a whole to fail.
Peer-to-peer architecture
— No hierarchy and no parent-child relationships are needed.
Quiet protocol
— Routing overhead will be reduced by using a reactive protocol similar to AODV.
Route discovery
— Rather than maintaining a network map, routes will be discovered and created only when needed.
Selective acknowledgments
— Only the destination node will reply to route requests.
Reliable delivery
— Reliable delivery of data is accomplished by means of acknowledgments.
Sleep modes
— Low-power sleep modes with synchronized wake-up are supported, with variable sleep and wake times.
2.4GHz DigiMesh Module Features
Power output: 1mW (+0 dBm)
Indoor/Urban range: Up to 100 ft (30 m)
Outdoor/RF line-of-sight range: Up to 300 feet (90 m)
RF data rate: 250 Kbps
Interface data rate: Up to 115.2 Kbps
Receiver sensitivity: -92 dBm
Spread Spectrum type: DSSS (Direct Sequence Spread Spectrum)
Networking topology: Mesh, point-to-point, point-to-multipoint, peer-to-peer
Error handling: Retries and acknowledgments
Channel capacity: 16 Direct Sequence Channels
Addressing: PAN ID, channel, and 64-bit addresses
Encryption: 128-bit AES
Supply voltage: 2.8V - 3.4V DC (Footprint Recommendation: 3.0V - 3.4V DC)
Transmit current: 45 mA (@ 3.3V)
Receive current: 50 mA (@ 3.3V)
Sleep current (pin sleep): <10 µA
Sleep current (cyclic sleep): <50 µA
Frequency band: ISM 2.4 GHz
Interface options: 3V CMOS Serial UART (5V-tolerant inputs)
Configuration method: AT and API
Digital I/O: 13 I/O lines
ADC: Six 10-bit analog inputs
Size: 0.960 in × 1.087 in (2.438 cm × 2.761 cm)
Weight: 0.10 oz (3g)
Operating temperature: -40°C to 85°C (industrial)
Certifications: FCC (USA), IC (Canada), ETSI (Europe), C-TICK (Australia), Telec (Japan)
Antenna options
Three other versions of this module are available:
with RP-SMA connector
with U.FL connector
with wire antenna
In addition, there is a
long-range version
available.
2.4GHz DigiMesh Module Resources
XBee DigiMesh 2.4 User Manual
Mechanical Drawing
Download X-CTU Configuration Utility
(click
Diagnostics, Utilities and MIBs
)
X-CTU User Manual
White Paper:
Wireless Mesh Networking: ZigBee vs. DigiMesh